The trade’s best kept secret

Ultra smooth floor leveller

checkbox-img.png Self-levelling for uneven floors
checkbox-img.png Ultra smooth finish perfect for vinyl, lino or carpet
checkbox-img.png Suitable for solid substrates

About this product

A polymer-modified, cement-based, self-smoothing levelling compound for use up to 30mm. It is used for correcting surface irregularities on interior floors.

Find your nearest store →

Features and benefits

  • Manufactured under BSI Quality Assurance Scheme ISO 9001
  • Excellent spreading and smoothing characteristics
  • Provides an ultra smooth finish
  • Rapid drying

Uses

For levelling:

  • Cement screeds
  • Concrete


Suitable for covering with:

  • Ceramic, porcelain and natural stone tiles
  • Carpeting
  • Flexible floor coverings (such as vinyl or lino)
  • Parquet flooring


Constraints

Not to be used where some movement is expected (eg under-floor heating). Do not use:

  • On exterior floors
  • On permanently damp floors or floors with rising damp
  • In Industrial areas
  • On friable or weak surfaces
  • On substrates where some movement is expected such as heated floors, an application of Weber Flexible floor leveller is required, once this has set it can be primed and a thin skim of Weber Ultra smooth floor leveller can be applied to receive flexible floor covering such as vinyl or lino.

Technical Data

Adhesion on concrete>1.0 N/mm2
Flexural Strength6 N/mm2
Compressive strength25 N/mm2
Particle sizeup to 1 mm
Working time (pot life)20 minutes
Self-smoothing open time15 minutes
Application thickness(light traffic) 2 to 30 mm
(medium traffic)4 to 30 mm
Delay for light foot traffic2 to 4 hours
Drying time before applying a covering
Ceramic tiles
Textile, plastic or wood
8 to 12 hours at 5 mm thick
24 hours at 5 mm thick

Note: The times quoted refer to +20°C and are longer at lower temperatures and shorter at higher temperatures. Strength values were obtained under laboratory conditions and may be significantly modified under site conditions.

Preparation

Substrates should be completely dry, hard, rigid and clean. Remove any traces of paint, plaster, laitance, old adhesive or other unsound materials. Thoroughly remove all traces of dust by vacuuming or sweeping.

Concrete should be a minimum 28 days old and have minimum compressive strength of 20 N/mm2.

The relative humidity of the substrate must be <95%.

Fill in any localised deep holes and allow to dry before applying the levelling compound.

Priming with Weber Tiling Primer will improve the screed’s adhesion to the substrate, prevent air bubbles, improve the flow of the screed and prevent de-watering.

Mixing

Do not mix if the temperature is outside of the range +5°C to +30°C.

Thoroughly mix 5 litres of clean water per 25 kg bag using a slow speed electric mixer (250 rpm) for at least two minutes until a fluid, homogenous paste is obtained.

Allow the mix to stand for 2 minutes, then use within 20 minutes.

At higher temperatures this time will be reduced.

Do not attempt to extend the pot life by the addition of more water.

Application

Pour the mix onto the floor and spread evenly with a steel trowel, spatula or spiked roller. Do not apply at thicknesses above 30 mm. The product will self-smooth and most trowel marks will disappear.

At 15 – 20°C Weber Ultra smooth floor leveller will have set sufficiently hard in 2 to 4 hours to withstand light foot traffic. Laying of the floor covering can then commence within 24 hours. At lower temperatures and at thicknesses over 5 mm, these times will be extended.

The minimum application thickness is 2mm (4 mm in heavier traffic areas and under tiling).

Weber Ultra smooth floor leveller is not intended as a wearing surface so the final finishing layer should be applied as soon as possible after drying has completed. If it is to be left for a prolonged period of time the surface should be suitably protected.

Allowance for movement

Allow for suitable expansion or control joints in screeds or slabs by following them through the new topping.

Packaging

Packed in 25kg plastic lined paper sacks.

Coverage

Coverage is approximately 1.7 kg/m2/mm of thickness.

Storage and shelf life

When stored unopened in a cool dry place at temperatures above 5°C, shelf life is 12 months from date of manufacture.

Health and safety

Contains cement (Contains chromium (VI). May produce an allergic reaction). Harmful by inhalation. Irritating to eyes and skin. Keep out of the reach of children. In case of contact with eyes, rinse immediately with plenty of water and seek medical help. After contact with skin, wash immediately with plenty of soap and water. Wear suitable protective clothing, gloves and eye/face protection.

For further information, please request the Material Safety Data Sheet for this product.

1.5mcoverage@10mmIcon.png
ApplicationDepth30mmIcon.png
OtherCoverings24hIcon.png
OtherCoverings24hIcon.png
Available-at-Homebase-Product.png
 

Product Selector

Not sure which product you need for your DIY project?

Our easy-to-use product selector can help!

Start

product-selector-person.png

 

To the best of our knowledge and belief, this information is true and accurate, but as conditions of use and any labour involved are beyond our control, the end user must satisfy himself by prior testing that the product is suitable for his specific application, and no responsibility can be accepted, or any warranty given by our Representatives, Agents or Distributors. Products are sold subject to our Standard Conditions of Sale and the end user should ensure that he has consulted our latest literature.