Fast set wall & floor tile adhesive
|For use on solid substrates|
|Fast setting to reduce time before grouting|
About this product
A cement-based floor and wall tile adhesive. For fixing ceramic, mosaic and quarry tiles to concrete, screeded concrete or plasterboard. Suitable for interior and exterior walls and floors.
Features and benefits
- Manufactured under BSI Quality Assurance Scheme ISO 9001
- Ready for light foot traffic and grouting after 2 hours
- Strong bond strength
- Available in grey
For fixing ceramic, mosaic and quarry tiles:
- Walls and floors
- Interior and exterior
- Tiling onto existing tiles
Not suitable for porcelain and natural tiles or where limited movement is likely i.e. wood or heated floors.
For these scenarios Weber Fast set wall & floor tile adhesive professional is recommended.
Exceeds the requirements of BS EN 12004 for C1FT
|Bed thickness||3 – 6mm|
|Coverage (approx.)||1 kg/m2 for every 1mm of bed thickness|
|Open time||10 minutes|
|Working time||30 minutes pot life after mixing|
|Set time||2 hours|
|Temperature resistance||5˚C - 35˚C (during application)|
–10˚C to 100˚C and frost resistant when set
Note: setting times are quoted at 20˚C and are temperature and humidity dependent
All surfaces should be clean, dry, sound, and free from grease, dust or any other contaminating barrier. Unsound areas should be made good before tiling. Flaky or peeling layers should be removed. Porous or dusty surfaces should be primed with Weber Tiling Primer and allowed to dry before tiling.
Check before use that the colour of the adhesive does not cause staining or discolouration of light coloured or translucent tiles.
Gradually add approximately 3.5 parts of powder to 1 part of clean water (measured by volume), and mix to a smooth workable, stiff paste. Normal usage requires 4.4 litres of water per 20kg of adhesive, for non-slip wall tiling 3.8 litres of water per 20kg.
Use within 30 minutes of mixing.
Do not attempt to extend the pot life by adding more water.
Do not use at temperatures below 5°C
Apply the adhesive onto the substrate covering up to 1 m2 at a time (or no more than can be tiled within 10 minutes). Use a suitable notched trowel to achieve a bed thickness of 3 to 6 mm. Large or studded backed tiles may need to have adhesive buttered onto the tile back as well.
Bed the tiles firmly into the adhesive with a slight sliding and/or twisting action, to ensure a good contact. It is good practice to lift an occasional tile after fixing, to verify that the required contact is being achieved. In external areas and all floors, the final adhesive bed should be free from voids.
Leave appropriate clearance joints for grouting and make any adjustments within 10 minutes.
Carefully clean off any excess adhesive from the tiles and joints with a damp cloth or sponge before it sets.
Leave for at least 2 hours before grouting. Longer is required at lower temperatures or when tiling onto impervious or sealed surfaces.
Brick and blockwork
Allow at least 6 weeks before tiling. Lightweight blocks need priming with Weber Tiling Primer. Ensure that the wall face is sufficiently flat.
Cement/sand render or screed
Allow at least 3 weeks for screed and 2 weeks for render before tiling. Priming may be required if the surface is very dusty or porous.
Allow at least 7 weeks before tiling onto new concrete. Surface should be clean and free from laitance – scabbling is recommended.
Existing ceramic/vinyl tiles
Ensure that the substrate is strong enough to take the weight of extra tiling, that the existing tiles are firmly adhered and that the surface is free from any wax or polish.
Plaster walls and anhydrite screeds
Leave plaster for at least 4 weeks before tiling. It is important that the surface is abraided and sealed by repeatedly coating with Weber Tiling Primer until the surface stops absorbing.
Wallboards; fibre/cement, plywood, plasterboard
Ensure boards are rigidly supported, clean, dry and free from dust. Plasterboard should be thoroughly primed with Weber Tiling Primer as should the back face and edges of plywood until surface stops absorbing.
Allowance for movement
Flexible joints should be incorporated to allow for slight movements due to changes in temperature, humidity etc. as indicated by BS 5385:
a)where the tiling meets other materials
(e.g. floor perimeters)
b) along all internal corners – vertically and horizontally
c) over existing movement joints or changes in background material
d)dividing large tiled areas into bays (every 3 – 4.5 m on walls, 8 – 10 m on floors)
Packed in plastic lined paper sacks. Grey: 20 kg.
Coverage is approximately 1.5 kg of powder per m2 for every 1 mm of bed thickness.
Storage and shelf life
When stored unopened in a cool dry place at temperatures above 5°C, shelf life is 12 months from date of manufacture.
Health and safety
Contains cement (Contains chromium (VI). May produce an allergic reaction). Harmful by inhalation. Irritating to eyes and skin. Keep out of the reach of children. In case of contact with eyes, rinse immediately with plenty of water and seek medical help. After contact with skin, wash immediately with plenty of soap and water. Wear suitable protective clothing, gloves and eye/face protection.
For further information, please request the Material Safety Data Sheet for this product.
Not sure which product you need for your DIY project?
Our easy-to-use product selector can help!
To the best of our knowledge and belief, this information is true and accurate, but as conditions of use and any labour involved are beyond our control, the end user must satisfy themselves by prior testing that the product is suitable for his specific application, and no responsibility can be accepted, or any warranty given by our Representatives, Agents or Distributors. Products are sold subject to our Standard Conditions of Sale and the end user should ensure that he has consulted our latest literature.